 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MODEL 5100 SERIES 7/8" Diameter Single Turn Wirewound Precision Potentiometer MODEL STYLES 2 5101 5103 ELECTRICAL 1/8" Shaft, 3/8" Bushing 1/8" Shaft, Servo Resistance Range, Ohms Standard Resistance Tolerance Minimum Practical Resistance Tolerance Independent Linearity Minimum Practical Independent Linearity Power Rating, Watts Dielectric Strength Insulation Resistance, Minimum Noise, Maximum Actual Electrical Travel Tap Tolerance End Voltage, Maximum ENVIRONMENTAL (MIL-R-12934) 200 to 15K 5% 2% 0.5% 0.25% 0.75 at 40C derating to 0 at 85C 1,000V rms 1,000 Megohms 100 Ohms 354 + 2 2 <500 Ohms, 1 500 Ohms Within Std. Linearity Tolerance Operating Temperature Range Temperature Cycling Shock, 6ms Sawtooth Vibration Humidity Rotational Load Life Specifications subject to change without notice. -25C to +85C 5 cycles, -25C to +85C 100G's 10G's, 10 to 500 Hz Five 24 hour cycles 500K shaft rev. plus 900 hrs. at rated wattage at 40C 2-39 Model 5100 Series MECHANICAL Total Mechanical Travel Number of Cups, Maximum Weight, Nominal Backlash Shaft End Play, Maximum Shaft Runout, T.I.R., Maximum Pilot Diameter Runout, T.I.R., Maximum Lateral Runout, T.I.R., Maximum Shaft Radial Play, Maximum Start/Run Torque, Maximum STANDARD RESISTANCE VALUES, OHMS 360 Continuous 4 0.5 oz. Single Cup 0.3 oz. Each Added Cup Negligible .005" .0015" .002" .003" 5101 5103 .003" .0025" 0.2 oz.-in. 0.2 oz.-in. Total Resistance 1K 2K 5K 10K 15K Theoretical Resolution (% Nominal) 0.210 0.170 0.140 0.110 0.100 Tempco of Wire 20 ppm/C 20 ppm/C 20 ppm/C 20 ppm/C 20 ppm/C METRIC CONVERSIONS 1 in. 1 oz. 25.4mm 28.4 gm 1 oz.-in. 1 lb.-in. 0,007 N-m 0,113 N-m 2-40 Model 5100 Series OUTLINE DIMENSIONS (Inch/mm) Model 5101 - Bushing Mount "RS" 1.200 .031 30.48 0.79 .700 "L" 17.8 .250 6.35 Min. Dimensions shown are with 1 cup, for each additional cup: increase "RS" by .500 12.7 .500.002 increase "L" by 12.7 0.05 Mounting Surface .500.031 12.7 0.79 + .0000 .1248 - .0003 Dia. + 0.000 3.170 - 0.008 + .000 .406 - .002 + 0.00 10.3 - 0.05 105 Max. CCW CW Clamp Ears Slider .625 R. Max. 15.9 + 2 .875.016 Dia. 22.2 0.41 .500.016 12.7 0.41 + .000 .062 - .010 Dia. + 0.00 1.575 - 0.25 .250 .005 Min. 6.35 0.13 Chamfer .016 Max. x 45 0.41 3/8 - 32 UNEF Thread OUTLINE DIMENSIONS (Inch/mm) Model 5103 - Servo Mount "RS" 1.200 .031 30.48 0.79 .700 "L" 17.8 .250 6.35 Min. Dimensions shown are with 1 cup, for each additional cup: increase "RS" by .500 12.7 .500.002 increase "L" by 12.7 0.05 Mounting Surface .500.031 12.7 0.79 + .0000 .1248 - .0003 Dia. + 0.000 3.170 - 0.008 105 Max. CCW CW Clamp Ears Slider .625 R. Max. 15.9 + .875.016 Dia. 22.2 0.41 + .0000 .7500 - .0005 + 0.0000 Dia. 19.050 - 0.0127 .875 .005 22.2 0.13 Dia. .781 Dia. Max. 19.8 .057 Min. 1.45 .062.005 Min. 1.58 0.13 Chamfer .016 Max. x 45 0.41 .062 .005 1.58 0.13 2-41 Model 5100 Series SPECIAL FEATURES Center Tap Linearity Tape Rear Shaft Extension Flatted Shaft Slotted Shaft ORDERING INFORMATION CT LT RS FS SS 5101 R 10K L.50 XX Model Series Resistance Prefix Resistance Value Linearity Optional Special Feature Code CIRCUIT DIAGRAM NOTES Metric equivalents, based on 1 inch = 25.4mm are rounded to the same number of significant figures as in the original English units and are provided for general information only. (S) (CCW) (CW) INCH mm Tolerances unless otherwise specified: Linear = .01 inches (.25mm) Angular = 2 degrees 2-42 Model 5100 Series |
Price & Availability of 5103
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |